NXP Semiconductors Kinetis W Microcontrollers
NXP Semiconductors Kinetis W Microcontrollers integrate class-leading sub-1 GHz and 2.4 GHz RF transceivers with ARM® Cortex® cores, providing robust feature sets for reliable, secure and low-power embedded wireless solutions. The Kinetis W series is optimized for wireless, providing the right mix of performance, integration, connectivity and security. The enablement packages include NXP's Tower System Development Platforms, MQX™ RTOS and support from IAR Systems. Whether you need sub-1 GHz or 2.4 GHz wireless, simple point-to-point or full mesh networking, the Kinetis W series has the solution to fit your needs.Features
- KW0x Features
- RF Transceiver
- Supports 290-340MHz, 424-510MHz, and 862-1020MHz frequency bands
- High sensitivity: down to -120dBm at 1.2kbps
- High selectivity: 80dB blocking immunity
- Low current: Rx = 16mA
- Programmable output: -18 to +17dBm in 1dB steps
- FSK bit rates up to 600kbps
- FSK, GFSK, MSK, GMSK and OOK modulations
- Packet engine with CRC, AES-128 encryption and 66-byte FIFO
- Built-in temperature sensor and low battery indicator
- MCU
- Ultra-low-power 32-bit ARM® Cortex®-M0+ core. 2x more CoreMark/mA than the closest 8/16-bit architecture. Single-cycle fast I/O access port facilitates bit banging and software protocol emulation, maintaining an 8-bit "look and feel"
- Multiple, flexible low-power modes including new compute mode which reduces dynamic power by placing peripherals in an asynchronous stop mode
- I2C, ADC, DAC, LP timer and DMA support low-power mode operation without waking up the core
- Memory
- 128 KB flash with 64 byte flash cache
- 16 KB RAM
- Peripherals
- 16-bit ADC with configurable resolution, sample time and conversion speed/power
- High-speed comparator with internal 6-bit DAC
- 12-bit DAC with DMA support
- Interfaces
- Capacitive touch sense interface supports external electrodes
- GPIO with pin interrupt support, DMA request capability and other pin control options
- One I2C with DMA support, up to 100Kbps and compatible with MBus V2 features
- One LPUART and two UART with DMA support
- Operating Voltage and Temperature Range
- 1.8 to 3.6V operating voltage with on-chip voltage regulators
- Temperature range of -40°C to +85°C
- Software
- Radio Test Tool
- Run on PC connected through USB
- Allow fast evaluation of the radio performance in a lab environment without need for writing software
- Analysis of TX spectrum (output power, harmonics)
- Modulation scheme impact (GFSK, BT, Mod index) on spectrum
- Help on matching network tuning
- Analysis of RX Sensitivity performance (RSSI, LNA input impedance, OOK threshold, AFC)
- SMAC (Simple Media Access Controller)
- Simple communication and test apps based on drivers/PHY utilities available as source code
- Small footprint (<10KB)
- Supports point-to-point and star networks with repeaters
- Support for over-the-air programming
- RF Transceiver
- KW2x Features
- Up to 50MHz Cortex-M4 with 16-channel-DMA
- 512KB Flash and 64KB RAM or
- 256KB Flash and 32KB RAM with:
- 64K FlexNVM (MKW21D256 only) and
- 4k bytes of enhanced EEPROM/FlexRAM
- SPI (1)
- UART (2)
- I2C (2)
- USB FS OTG (KW22 and KW24)
- 8-channel 16-bit SAR ADC
- 6-bit DA
- Cryptography Acceleration Unit (CAU)
- AES encryption (FIPS 140)
- External tamper detect
- 32-bit CRC
- 1.8 to 3.6 volts
- Low-voltage detection
- Multiple low power modes
- Operating temperature of -40°C to 105°C
Applications
- In-home displays
- Smart thermostat
- Metering
- Home energy gateways
- Security and access control
- Smart grid and smart metering
- Building control and monitoring
- Building HVAC control
- Retail pricing management
- Usage data collection
- Water heater control
- Home health care
- Patient monitoring
- Fitness monitoring
Videos
KW0x Block Diagram
KW2x Block Diagram
Published: 2014-01-20
| Updated: 2025-06-24
